DTG Pretreatment: Solutions, Steps and Fabric Notes
DTG pretreatment is the liquid layer that lets white ink sit on a dark cotton shirt instead of sinking into the weave. Hongsam, founded in 2001 and based in Zhengzhou, Henan, supplies pretreatment liquids and DTG inks for cotton garment printing.

What Is DTG Pretreatment and Why It Matters
DTG pretreatment is a liquid applied to the garment before digital printing. On a dark cotton t-shirt its job is part mechanical, part chemical: it gives white ink a surface to sit on rather than letting it soak into the weave, it reduces ink bleeding along the edges of a design, and it supports colour brightness, pattern definition and colour fastness after washing. Without that layer, white ink has little to anchor to and the print reads thin and uneven.
- Pretreatment liquid applied to the shirt and dried
- White ink and colour ink printed onto the prepared surface
- Pre-drying to drive off water from the wet print
- Final curing in a heat press to bond pigment to fibre
The order of those steps matters more than any single setting. Fabric, ink and equipment settings all move the result, so a recipe that works on a light cotton knit will need adjusting on a heavier loopback or a blended fabric. Hongsam advises preliminary experiments before use and adjusting equipment, process and prescription to actual production conditions and fabrics.
Pre Treatment DTG: Where It Sits in the Print Workflow
Pre treatment DTG sits between garment preparation and ink.
Skip the step and the losses show in a few places. White ink opacity drops because the ink follows the fibre instead of resting on top of it. Edge sharpness softens as ink wicks outward along the threads. Wash durability weakens because there is no polymer film holding pigment at the surface, so the print abrades away from the cotton.
Cotton and cotton-rich knits in dark shades are the group that normally needs pretreatment, and the same applies to blends carrying a polyester share. Light shirts printed with colour ink alone often run without it, because there is no white layer to build and no opacity to protect.
Direct to Garment Pretreatment vs Other Fabric Preparation Methods
Direct to garment pretreatment is applied to a finished, cut shirt. Spraying by hand or with a spray unit, roller application and padding all work, and the shirt is dried and pressed before printing. The equipment is small and garment-scale: a spray station or padder, a drying oven or heat press, and the printer itself.
Pad-batch pretreating and coating pre-treatment belong to roll fabric, not garments. Padding saturates a continuous length through a mangle before washing and drying; coating lays a thin film on a direct-to-fabric line. Hongsam supplies a Coating Pre-treatment Liquid for Direct-to-Fabric Pigment Ink Printing, designed for the pre-treatment of textiles prior to direct-to-fabric coating printing, and the textile pigment ink range serves those routes.
The route follows the product. A printed t-shirt needs a garment-scale spray or pad step; a roll of cotton knit headed for cut-and-sew needs a continuous coating or pad-batch line, with drying capacity matched to line speed rather than to shirt count.
Choosing a DTG Pretreatment Solution
Selection turns on fabric type and pigment ink chemistry. The liquid must wet out the fibre, leave a film that white ink can grip, and stay compatible with the ink and the printhead in use. Dilution with soft or purified water, polymer solids, shelf life and storage conditions all change how a batch performs, so one concentrate can behave differently on a cotton interlock and on a polyester blend.
HONGSAM PP-17 Pre-treatment Liquid for Textile Pigment Ink is a listed Hongsam product whose stated fabric range covers cotton, polyester/cotton, brocade cotton, hemp, polyester ammonia, Modal, nylon and other blended fabrics. Contact with printheads and inks is to be avoided, and it should not be mixed with other auxiliaries.
DTG Polyester Pretreatment: Blends, Curing and Hand Feel
Polyester and polyester-cotton do not behave like 100% cotton under a DTG printhead. The fibre is thermoplastic, so it tolerates less heat before the surface glazes, and disperse dye already in the fabric can migrate into the white layer during curing. Hand feel shifts too: a heavy polymer film on polyester reads stiffer than the same film on cotton.
Coverage, drying temperature and curing time are the levers. A lighter, evenly sprayed film, thorough drying before printing and a cure that stays inside the fibre’s tolerance limit reduce migration and keep the hand soft. On blends, the cotton share takes the pretreatment and the polyester share sets the heat ceiling.
PP-17 pre-treatment liquid for textile pigment ink lists polyester/cotton and polyester ammonia among its fabric types, which places those blends inside its stated range. Where the ink system itself is still open, a pigment versus dye comparison helps before the pretreatment is fixed.
Pre Treated Shirts for DTG: Storage, Shelf Life and Reprinting
A pre treated shirt has already received the pretreatment liquid and been dried, either in-house or on supplied blank stock. It prints like a prepared garment, but the film picks up moisture and dust in storage and loses effectiveness over time, so treated stock rotates faster than untreated stock.
Store treated shirts cool and well ventilated, away from freezing and direct sunlight.
Re-pressing a treated shirt flattens the fibres and can reactivate a slightly damp film, which helps the print sit level. Spraying a second layer over an old one adds solids and stiffens the hand, so a re-spray is better done on untreated stock.
Pretreatment for DTG Printing: Step-by-Step Application
- Dilute the liquid as directed, using soft or purified water.
- Spray uniformly on dark fabric, then dry the shirt; optional drying at an elevated temperature sets the film.
- Press the print area flat so the surface is level.
- Print white and colour ink.
- Pre-dry at a moderate temperature, then cure in the heat press for a few minutes at the higher setting.
The sequence holds on manual stations and on small conveyor setups alike. What changes is how long the shirt spends at each stage, and that is set by the fabric weight, the moisture left in the film and the ink load of the design.
Hongsam advises conducting preliminary experiments before use and adjusting equipment, process and prescription to the actual production conditions and fabrics. A test shirt run through the full sequence, washed and inspected, says more than a setting copied from another fabric.
DTG Pre Treatment Problems: Yellowing, Fading and Stiff Prints
- Excess liquid: the film stays wet, curing is uneven and the hand turns boardy. Reduce spray volume and dry fully.
- Uneven spray: patches of weak white and soft edges. Work in overlapping passes and check the shirt under raking light.
- Yellowing: usually heat rather than the liquid, from too hot a cure or too long a press cycle on the polymer and fibre.
- Fading after washing: under-cured film or too little polymer at the surface. Re-check cure dwell and coverage.
- Rough hand feel: too much solid on the surface, or a second layer sprayed over an old one.
PP-17 pre-treatment liquid for textile pigment ink is to be kept away from printheads and inks, and it must not be mixed with other auxiliaries. Cross-contamination of that kind shows up as printhead faults rather than print faults, and it is harder to trace back.
Applied correctly, the pretreatment is intended to raise colour brightness, pattern definition and colour fastness together. When one of those three falls short while the others hold, the cause is usually application or cure rather than the liquid itself.
Epson Polyester Pretreatment: Matching Ink, Head and Fabric
Ink and pretreatment are chosen as a pair, and both follow the printhead family and the fabric. A head that lays down a fine drop needs a liquid that leaves a smooth, even film; a polyester blend needs a heat budget the fibre will accept without glazing or dye migration.
Hongsam’s JETTEXTILE® DTG white ink is listed for Epson heads among other head families, and the DTG ink supports both wet and dry printing. Hongsam supplies a one-stop solution covering garment printer, DTG ink, pre-treatment liquid, cleaning fluid and printhead protection liquid, with garment printers offered under the Hong-Jet® brand.
Confirm the head model and the blend composition before ordering. The ink grade, the pretreatment and the printer settings follow from those details, and a sample print on the actual fabric settles the remaining process questions before the order is placed.
Request a quotation
Share your printer, substrate and the result you want to reach.
Or write to sales@inkjetinksupplier.com